Raycor Garage Door Lock - Rekeying Procedure Without New Tumblers

 About 6 weeks ago we took a call from a customer who requested service that no one else would provide,

The customer has an old Raynor brand garage roller door on her garage and wanted to have the lock rekeyed.

This door is about 75 years old and all the companies she called (before me) would not work on the existing product, preferring to instead attempt to talk her into buying a new automatic roller door.

After becoming annoyed at not having her needs met, her search for service led her to find me.

This first image shows the Raynor Operating handle and key cylinder from the outside.

 You can see in this second image, the configuration of the inside mechanism and how the lock and handle attaches to the door.

The chains on each side are attached to spring loaded "latches" that firmly hold the door when closed, into the running tracks.

It is not necessary to remove the lever handle to work on the key cylinder, simply remove the four screws to pull the lock casing from the frame.

The rim cylinder is quite old and still functioning well for it's age even though it appears to be slightly corroded.

The tailpiece is secured with a roll pin through the back of the cylinder plug/barrel

Here is another view of the rear of the cylinder. You can see the roll pin sitting through the tailpiece and the back of the barrel

This is an image with the roll pin and tailpiece removed

This image shows the plug/barrel with each pin tumbler removed

 We set the plug up with the new keyblank inserted, into our vise after switching some tumblers around to "alter the combination" making it different to the original key.

Measuring the new key blank and the existing plug with the new combination pins correctly inserted

 Next, we marked each corresponding spacing of each pin tumbler using our impressioning file.

Using the impressioning file to "cut" the new key directly from the pinning

 A different angle shows the progress being made in forming the new key

 Slow and steady processes, are important to maintain meticulous and exact work. We only file a little at a time and constantly check and recheck our work, so we dont "mess" it up.

This helps to make sure we do not ever need to replace parts if we accidentally lost them because we wont.

Careful processes lead to positive results

The key is almost completed

 Constantly rechecking our work to ensure the best quality.

 The completed "new key" is the brass one. The old key is the silver one we are changing

Completed and rebuilt without the need to replace anything.


Now, you can purchase after market cylinders still for these doors, but I am old school and prefer to keep as much original as i can.

One reason is that manufactured items in previous years were often produced to a higher standard and designed to last.

Unlike many of the products found in the modern era that are deliberately made using inferior raw materials and streamlined processes that often punch out significantly greater quantities while giving up quality control, in the sole intention of making sure consumers are required to constantly be purchasing new and replacement parts. (thereby keeping manufacturers in business).



The art of the craft of locksmithery can be very interesting to us old time trades people. This is just another example of the types of requests we locksmiths receive.

A Stroke Of Genius - Kwikset Smartkey Defeat With No Damage

Yesterday we attended to a client for whom we had previously rekeyed their new home about 8 weeks ago, who had accidentally locked themselves out.

The husband and wife had traveled out of state for a vacation and one of the spouses had inadvertently left their spare key inside the house, while the other spouse with the key was still interstate.

The types of locks they have on their doors are Kwikset Smartkey designer series locks similar to the style presented in the picture here.

Typically, many locksmiths would choose to drill and destroy a Kwikset Smartkey lock because typically they can be somewhat difficult to manipulate without causing unrepairable damage.

Many doors that use Kwikset Smartkey locks, tend to have a separate entry set from a deadbolt lock. Often defeating an entry set, without damage is painlessly simple and there are methods to bypass a Kwikset Smartkey deadbolt that are considered "outside the box". We deliberately choose NOT to share these unique bypass methods for fear of those details getting into the wrong hands.

Our customer being out of state, while their spouse was on their way home without a copy of their Kwikset Smartkey operating key, contacted me to attend the site and unlock the door on behalf of their spouse. When the spouse arrived at the airport they contacted me to arrange a suitable time.

Being as cold as it is presently, I did not want to keep the customer waiting for long while I attempted to manipulate the lock cylinder. I did not want to drill and destroy the lock, because getting a replacement on such short notice was not possible, so I asked the spouse interstate to snap a picture of their operating key and text it to me.

Upon receiving the image, I attended the home just prior (about 15 minutes) before the spouse arrived home from the airport. I grabbed the appropriate Kwikset key blank and set about making a copy of their operating key with my handheld impressioning file.

Having a clear image from which to determine the cuts of the key proved the stroke of genius in this move, because I was able to recreate the operating key in about 10 minutes and it operated flawlessly in the deadbolt (pictured above). This allowed me to unlock their door without any damage nor signs of forced or manipulated entry. The clients existing key (inside the house) still worked like new and we saved the inconvenience of trying to replace a special order lock product.

NOW - Obviously you can see a security issue here that can be distressing. If someone has enough time to take a picture of your house key, potentially they could simply contact a locksmith who could also provide the same service and make a copy of the key. Ethically and morally many locksmiths would not do this, unless they knew the customer and they could prove they belong to the address in question. But not everyone lives by a code of ethics.

A few years ago we wrote an article that talked about creating key duplicates using the credit cards you often get on the mail from promoters.

See Credit Cards Used To Duplicate Keys

Another article we wrote about 5 years ago talked about a service created by some enterprising engineers in California called Shloosl, See the link

Here is an article from about 10 years ago that discusses the ease in creating a copy of your key by picture..... Key Photograph Key Cutting


Simply put, there is only 1 way to prevent unauthorised key duplication. Using a High-Security Restricted Key System. Systems that require your signature authorization in advance of origination. There are many systems available across the world in today's market. Some better than others. We choose to offer the Bilock Extreme Security restricted key system.

Lockwood 7444 Keyed Pocket Door Lock And Range To Be Discontinued By Us

After careful consideration, we have decided to discontinue selling this product.

We have been selling this product for 9 years and due to rising costs and reducing sales (even being significantly cheaper than competitors), we have decided to discontinue representing this type of pocket door lock in North America.

In the last 9 years we have sold thousands of this product with repeat customers ordering again and again to satisfy the needs of their clients.

We will sell our remaining inventory (about 18 keyed units and 10 privacy sets and 10 passage sets) at a fire sale discount until no more product remains.

We expect to change the sales page with the new discounted price in the next few days.

Thank you all for your continued interest in this fabulous product and we hope you can still purchase it in future from other providers.

Strikemaster II To The Rescue - Again

 This week, we were called to another Home Advisor door repair project for a client who experienced door frame failure.

The image to the right here, shows the Strikemaster II product installed to repair the busted door frame. This particular installation required me to check the entire 5' strike plate into the existing frame after removing the weather stripping.

The Strikemaster II used here is NOT the Strikemaster II Pro, which is the updated product. We used the older product because the door, on a house built in the 1960's, was a very tight fit in its opening and the clearance between the door and frame when closed was about 1/16th". The typical gap around the edges of a door within it's frame should be 1/8th". This allows for weathering or frame movement if the house settles.

The second image shows the trim moulding removed. We had some difficulty sourcing replacement moulding because the width of the required moulding was 1-3/4" wide. That size hasnt been produced since at least 1970. All door trim moulding found today is a minimum 2" wide. We managed to source a supplier who could rip a new piece of moulding to enable to install it to the 1-3/4" frame and allow for the trim to neatly fit inside the brick clad wall, without having to damage the existing clad brick.








And the final image shows the new moulding reattached to the frame, ready for painting.

Being that the average door and frame replacement cost in our local region is ~$1100 - $1500 commonly, using a Strikemaster II or the newer Strikemaster II Pro can cut repair costs and time down to less than $300 total.

UFO3 - New Improved High Security Lock For Vans and Cargo Vehicles

We have been the North American distributors for the broad range of Meroni products for about 8 years now and recently aligned with another distributor based in Minnesota who is distributing the fabulous UFO range of high-security locks for delivery vans, tradespeople vans, trucks among other applications. The new distributor is in  Minnesota will cater primarily to the automotive sector with this product line. We will continue to support them with key duplication and creation requests.

You can see our articles already written about the UFO range by Meroni by clicking here

The above video shows the installation steps for the newest model the UFO3.

The straightforward installation procedure can be handled easily by a trained technician or almost anybody, provided they have the correct tools and follow the guidelines in the instructions.

There is another new product, recently developed with Meroni in Europe aimed at UFO range of high-security automotive locking products that is a Cloud-Controlled access control system designed for fleet operators to enable simple access control for their fleets of deliver and transportation vehicles.

The UFO Cloud is a system that uses the SHA256 Encrypted Communication Protocol based on the design developed by the NSA.

The practicality of the UFO Cloud, transforms mechanical keyed products into a virtual keychain using a cellphone app and dedicated dashboard.

For further details on the UFO Cloud and the wide range of UFO products by Meroni, check the source below.

(source...)

Door Transformations - Modifying Your Entry Door To Increase Curb Appeal

A few years ago, we held a booth at the St Louis Home Show to display our unique ranges of products and services.

While there, we met a company that provides a unique service to homeowners that can modify an existing solid door to a beautiful glass door insert that often can cost about half the cost of replacing your existing door with a new door and frame.

Yesterday, we attended to a returning customer requesting us to install a new replacement lock on their existing storm door (that a handyman was unable to perform) and the client spoke to us about getting a new door that included a glass window in it, to provide more light at the entry.

We remembered the company we met a few years earlier and recommended them to the client, because their existing door had already been modified from a double door to a single door, but the contractor did not replace the existing double door with a new door and frame, they just built the inside staircase and walled in the fixed leaf. this would make it significantly more expensive to have the door and frame removed to install a more aesthetic entry door to their liking.

Entrypoint are an interesting company based in the St Peters Missouri area that provide the unique service  as described in the above video.

This is a product and service that we are also exploring to beautify our own entry door at our home too.

When you consider the cost to replace the door and frame with a completely new installation, modifying your existing door is a significantly more competitive option worth considering.

Entrypoint's site is in the source below.

(source...)

Today Marks Our 12th Birthday

We started our business December 26, 2006 and being our 12th birthday today we have decided to offer a special deal for the next 12 months.

Here forward, for the next twelve months we will offer a 12% discount on any and all parts purchased through us. The 12% discount will apply only on the 12th business day of the month.

January - Wednesday January 17th, 2019
February - We will be closed. Apologies.
March -  Monday March 18th, 2019
April - Tuesday April 16th, 2019
May - Thursday May 16th, 2019
June - Tuesday June 18th, 2019
July - Tuesday July 16th, 2019
August - We will be closed. Apologies.
September - Tuesday September 17th, 2019
October - Wednesday October 16th, 2019
November - Monday November 18th, 2019
December - Tuesday December 17th, 2019

The special 12% discount will apply before tax and is in addition to any other discount offered.
The discounts apply to all purchases of parts (not labor) whether online or offline.

We take this opportunity to thank our many customers for their trust and their custom. We look forward to your continued custom.

Warm Regards,
Danny Gurvis
President
Master Key Systems America LLC
https://locks210.blogspot.com/
314-266-1533

AI Powered 3D Security Camera Manufacturer Closes Down

Back in mid 2017, a new company formed to produce and sell an ambitious new product called the Lighthouse AI Security Camera.

Well known former Google manager Andy Rubin was instrumental in the development of this technology.

Well, another one bites the dust....

The company just announced that they are closing due to insufficient sales orders of the revolutionary product.


Originally the company claimed...

The camera is powered by AI and a 3D sensor that can supposedly distinguish people from pets and recognize faces. Its onboard laser (similar to the 3D sensing devices used by self-driving cars) can measure the structure of what it sees and therefore differentiate objects and people from one another. Because of this capability, Lighthouse promises that you won't be bothered by false security alerts from shadows or pets because the camera can tell small objects from large ones.

The AI also understands normal speech patterns, so you can ask the camera questions like, "Did anyone walk the dog between 10 and 11 am?" The different types of tech within the camera work in tandem to deliver a full experience.

"Custom optics for a time-of-flight camera that directly measures the 3D structure of the environment," CEO Alex Teichman says in a blog post. "Recurrent neural networks for computer vision specifically tailored for use cases within the home. And a natural language interface to simplify -- and amplify -- the user experience."

A announcement on their website (in the source) below explains they are shutting down and closing their doors. It seems apparent that not enough customers were happy to pay $300 for each unit and a $10/month access fee for this advanced technology.

The announcement thanks their few customers for their interest.

(source...)